Описание на русском · Доступен перевод
GB18564.2-2008
Road tanker for dangerous liquid goods transportation - Part 2: Technical requirements of atmospheric pressure non-metal tank
道路运输液体危险货物罐式车辆 第2部分：非金属常压罐体技术要求
GB 18564.2-2008 — действующий обязательный национальный стандарт Китая: Road tanker for dangerous liquid goods transportation - Part 2: Technical requirements of atmospheric pressure non-metal tank. Отрасль: Электроника. Тема: Безопасность продукции. Дата вступления в силу: 1 июл. 2009 г..
Применимость зависит от продукции, схемы сертификации, уведомлений компетентных органов и переходных правил. Закажите перевод или проверьте источник, прежде чем использовать эту запись в решениях по соответствию.
Обзор требований
Этот обзор пока доступен только на английском языке.
Область применения
This standard is mandatory and applies to the design, manufacturing, testing, and inspection of non-metal atmospheric pressure tanks used in road tankers transporting liquid dangerous goods. It specifically covers tanks made of polyethylene (PE), polyvinyl chloride (PVC), polypropylene (PP), and glass fiber reinforced plastics (GFRP) with a working pressure of less than 0.1 MPa. This standard is not applicable to metal tanks, vacuum insulated tanks, military tanks, tanks with a volume greater than 20m³, or tanks carrying extremely or highly hazardous toxic media. It is intended for tanks permanently connected to a vehicle chassis or semi-trailer frame.
Технические требования
The standard specifies comprehensive requirements for non-metal tank materials, including mechanical properties and corrosion resistance. For GFRP tanks, it mandates a multi-layer wall structure consisting of an inner surface layer, a secondary inner layer, a strength layer, and an outer surface layer, with specific resin content requirements for each. Design requirements include calculations for design pressure, design temperature, and allowable stress based on the specific plastic material used. The standard outlines formulas for calculating the minimum thickness of the tank body and heads, taking into account static and dynamic loads during transportation. Manufacturers must ensure the tank's design pressure is not less than the maximum working pressure and that the calculated thickness accounts for external pressure stability. Manufacturing processes are strictly regulated, covering plastic welding, rotational molding, and GFRP lamination. The standard requires non-destructive testing (NDT) for welds and laminated structures, including radiographic, ultrasonic, and penetrant testing, to ensure structural integrity. It also details the installation of safety accessories, such as emergency shut-off devices and venting devices.
Методы испытаний
The standard mandates a hydrostatic pressure test as the primary method for verifying the tank's structural integrity, with the test pressure set to the tank's calculated pressure. For rotational molded PE tanks and GFRP tanks, mechanical property testing (tensile strength) is required using samples cut from the manhole area. Additionally, pneumatic testing is required for loading and unloading hoses, and specific NDT methods—radiographic for welded joints, ultrasonic for rotational molded tanks, and penetrant testing for nozzles and flanges—are specified to detect internal and surface defects.
Частые вопросы
What types of materials are covered under GB 18564.2-2008?
This standard covers non-metal tanks made from polyethylene (PE), polyvinyl chloride (PVC), polypropylene (PP), and glass fiber reinforced plastics (GFRP). It specifies different technical requirements and manufacturing processes for each material type.
What is the maximum working pressure allowed for tanks under this standard?
The standard applies to atmospheric pressure tanks with a working pressure of less than 0.1 MPa. Tanks operating at or above this pressure threshold fall outside the scope of this standard.
Are there specific temperature limits for the non-metal materials used in these tanks?
Yes, the standard specifies allowable temperature ranges. For PVC and PP, the range is -10°C to 50°C, while for PE and GFRP, it is -20°C to 50°C. The surface temperature of tank components must not exceed these limits under any circumstances.
The summary above provides a high-level overview of GB 18564.2-2008. To ensure complete compliance for your products entering the Chinese market, a precise and professional translation of the full technical specifications is essential. Purchase our high-quality English translation of GB 18564.2-2008 today to access all detailed parameters, tables, and testing procedures.
Подсказки по применимости
- Тип
- Продукция
- CCS
- T59
- ICS
- 43.160
- Компетентное ведомство
- Ministry of Industry and Information Technology
- Технический комитет
- Ministry of Industry and Information Technology
Связи
Частично заменяет:GB 18564-2001